However, Router will only prompt for to load firmware if the installed version is OLD (reverting is not expected).
#N1mm rtty install
Each Router install file includes a firmware file. 73 Thomas PA1Mġ.1 General information 1.1.1 Firmware updates and router versions It is neccesary to have loaded the CORRECT firmware version for each version of Router. The MK2R+ is a very complex hardware/software combination as it can be set up in so many different ways. The setup below is working for us but might not work at your place. This information is placed on the web in the hope that it may help others in setting up the microHAM MK2R+ SO2R controller. Thanks to Tom, N1MM for adding the microHam protocol to N1MM logger. Especially Id like to thank Joe, W4TV and Pete, N4ZR for all information they have put on the web, reflectors and in personal e−mail to us. Id like to thank all who have written about the MK2R+ in combination with N1MM logger.
#N1mm rtty serial
The shack PC at PA1T has 3 serial ports, so only 5 virtual ports are left to use and the LPT port is used. As an example: My PC has only 1 serial port so there is room for 7 virtual ports in uRouter in combination with N1MM logger. Choices have been made depending on the equipment used at these stations (PC, Radios etc). The information decribed is being used at the stations PA1T (Timon) and PA1M (Thomas). Also information from the N1MM and microHAM reflector are used and of course own trial and error.
![n1mm rtty n1mm rtty](https://www.oz1qx.dk/images/MMTTY_1_Setup.png)
![n1mm rtty n1mm rtty](https://www.rttycontesting.com/wp-content/uploads/2016/07/n1mm-0075.jpg)
The original text from Joe, W4TV has been used as a start for this document and updated with texts from Pete, N4ZR his SO2R−only document.
#N1mm rtty how to
(what to check when it does not work).50 4.5 How to setup RTTY (by Rich VE3KI).50 4.6 Best exchange format.51 4.7 Welcome to RTTY Contesting.52 4.8 Starting in September.53ġ General information (setting up microHAM and N1MM logger) In this document information is gathered about setting up the freeware contest program N1MM logger with the microHAM MK2R+ SO2R controller and Station Master banddecoder. 2 1.2.1 Proposed Virtual Port numbers.2 1.3 N1MM logger.5 1.3.1 "PTT line" (usually RTS) on a serial port.5 1.4 Station Master information.5 1.5 microKEYER (discontinued).6 1.6 Elecraft K3.6 1.7 Icom radios.7 1.8 Kenwood radios.7 1.9 All other Radios.7 1.10 Realtek sound card drivers and MK2R+'s USB Voice CODEC.8 1.10.1 One soundcards installed (only Realtek).8 1.10.2 Ok I have the realtek problem.9 1.10.3 Ok I have more than 3 mixers.9 1.10.4 Two soundcards installed (disable Realtek and use the other.).10 2 PA1M − MK2R+ and N1MM logger setup.11 2.1 Radio settings.11 2.2 microHAM Router setup.12 2.3 N1MM logger setup.20 2.4 MMTTY setup.25 2.5 PC setup.28 3 PA1T − MK2R+ and N1MM logger setup.29 3.1 Radio settings.29 3.2 microHAM Router setup.30 3.3 N1MM logger setup.38 3.4 MMTTY setup.43 3.5 PC setup.46 4 N1MM − RTTY operation / settings.48 4.1 MMTTY setup.48 4.1.1 Configure it to use the EU1SA profile.48 4.2 N1MM logger − RTTY − Operating the contest.49 4.3 QSO making tips with N1MM logger.49 4.3.1 Using Hover mode.49 4.3.2 The rate improver − Right Click = Enter not menu".49 4.4 Do you have. Table of Contents 1 General information (setting up microHAM and N1MM logger).1 1.1 General information.1 1.1.1 Firmware updates and router versions.1 1.1.2 Router software.1 1.1.3 Info on the web (used in this guide).1 1.2 MK2R+. N1MM logger Version: 7.11.0 microHAM Router Version: 5.03 Last update: NovemCopyright 2007, Thomas Tinge (PA1M)
![n1mm rtty n1mm rtty](http://n1mmwp.hamdocs.com/wp-content/uploads/2019/04/GRITTY-window.png)
Setting up N1MM logger with the microham MK2R+